| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 2<\/td>\n | undefined <\/td>\n<\/tr>\n | ||||||
| 4<\/td>\n | English CONTENTS <\/td>\n<\/tr>\n | ||||||
| 6<\/td>\n | FOREWORD <\/td>\n<\/tr>\n | ||||||
| 8<\/td>\n | INTRODUCTION <\/td>\n<\/tr>\n | ||||||
| 10<\/td>\n | 1 Scope 2 Normative references 3 Terms and definitions <\/td>\n<\/tr>\n | ||||||
| 11<\/td>\n | 4 Abbreviated terms and acronyms 5 General description 6 Applicability, reproducibility and complexity 6.1 General 6.2 Applicability <\/td>\n<\/tr>\n | ||||||
| 12<\/td>\n | 6.3 Reproducibility 6.4 Complexity 7 Measurement procedure 7.1 Stabilisation of the polymeric materials 7.2 Sampling and measurement locations <\/td>\n<\/tr>\n | ||||||
| 13<\/td>\n | 7.3 Conditions for measurement 7.4 Instrumentation <\/td>\n<\/tr>\n | ||||||
| 14<\/td>\n | 7.5 Calibration and tolerances Figures Figure 1 \u2013 Geometry and dimensions of the profile of the probe tip (truncated cone) used in the indenter Figure 2 \u2013 Penetration depth for full contact on the tip of the anvil <\/td>\n<\/tr>\n | ||||||
| 15<\/td>\n | 7.6 Selection of measurement points 7.7 Selection of probe velocity and maximum force 7.8 Clamping 7.9 Determination of the value of the indenter modulus <\/td>\n<\/tr>\n | ||||||
| 16<\/td>\n | 7.10 Reporting Figure 3 \u2013 Calculation of indenter modulus <\/td>\n<\/tr>\n | ||||||
| 18<\/td>\n | Annex A (informative) Examples illustrating factors affecting the variation of the indenter modulus value A.1 Example of influence of variability in equipment dimensions and construction A.2 Examples of temperature dependence Figure A.1 \u2013 Example of local variation of indenter modulus due to variation in equipment dimensions and construction <\/td>\n<\/tr>\n | ||||||
| 19<\/td>\n | Figure A.2 \u2013 Indenter values measured at different temperatures <\/td>\n<\/tr>\n | ||||||
| 20<\/td>\n | A.3 Examples of effects on the indenter modulus from drying out after high temperature ageing Figure A.3 \u2013 Normalised indenter mean values <\/td>\n<\/tr>\n | ||||||
| 21<\/td>\n | Figure A.4 \u2013 Example of change of indenter modulus value in laboratory conditions of a hygroscopic sample after removal from long-term exposure in a heat chamber Figure A.5 \u2013 Adaptation of a decay curve to the measured indenter modulus values in Figure A.4 <\/td>\n<\/tr>\n | ||||||
| 22<\/td>\n | Annex B (informative) Example of a measurement report for indenter measurements in laboratory Tables Table B.1 \u2013 Example of a measurement report for indenter measurements in laboratory <\/td>\n<\/tr>\n | ||||||
| 23<\/td>\n | Figure B.1 \u2013 Example of measured force versus time <\/td>\n<\/tr>\n | ||||||
| 24<\/td>\n | Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Nuclear power plants. Instrumentation and control important to safety. Electrical equipment condition monitoring methods – Indenter measurements<\/b><\/p>\n |