{"id":34578,"date":"2024-10-17T04:28:39","date_gmt":"2024-10-17T04:28:39","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/astm-b216\/"},"modified":"2024-10-24T14:48:13","modified_gmt":"2024-10-24T14:48:13","slug":"astm-b216","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/astm\/astm-b216\/","title":{"rendered":"ASTM-B216"},"content":{"rendered":"

ASTM B216-10<\/h3>\n

Historical Standard: Standard Specification for Tough-Pitch Fire-Refined Copper\u2014Refinery Shapes<\/h4>\n
\n

ASTM B216<\/h4>\n

Scope<\/strong><\/p>\n

1.1 This specification establishes the requirements for tough-pitch fire-refined copper wire bars, cakes, slabs, and billets for fabricating into wrought products and ingot and ingot bars for use in the manufacture of copper and copper alloy castings. This copper is not intended for electrical purposes.<\/p>\n

1.2 Copper under this specification corresponds to the designation \u201c<\/span>FRTP\u201d<\/span> (UNS C12500) as shown in Classification B224. This copper may also be used to produce copper, corresponding to the designation \u201c<\/span>DPTE\u201d<\/span> (UNS C14520).<\/p>\n

1.3 Although this specification includes certain UNS designations as described in Practice E527, these designations are for cross reference only and are not specification requirements. Therefore, in case of conflict, this ASTM specification shall govern.<\/p>\n

1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.<\/p>\n

1.5 The following safety hazard caveat pertains only to the test method described in the annex of this specification:<\/span> This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.<\/span><\/span><\/p>\n

A1.1.1 This test method covers the analysis of antimony, arsenic, bismuth, lead, nickel, selenium, and tellurium in tough-pitch fire-refined copper.<\/p>\n

A1.1.2 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.<\/span><\/p>\n

Keywords<\/strong><\/p>\n

fire refined copper; refinery shapes; tough pitch copper; Copper (refined\/refinery shapes)–specifications; Tough pitch coppers; UNS C12500 (fire-refined tough pitch copper, FRTP); UNS C14200 (phosphorus deoxidized copper, arsenical (DPA)); UNS C14500 (phosphorus deoxidized copper, tellurium bearing)<\/p>\n

ICS Code<\/strong><\/p>\n

ICS Number Code 77.150.30 (Copper products)<\/p>\n

DOI:<\/strong> 10.1520\/B0216-10<\/p>\n<\/div>\n

PDF Catalog<\/h4>\n\n\n\n\n\n\n\n
PDF Pages<\/th>\nPDF Title<\/th>\n<\/tr>\n
1<\/td>\nScope
Referenced Documents
Terminology
Ordering Information
Material
Chemical Composition <\/td>\n<\/tr>\n
2<\/td>\nDimensions, Mass, and Permissible Variations
Workmanship, Finish, and Appearance
Sampling
Number of Tests and Retests
Specimen Preparation
Test Methods
Significance of Numerical Limits
Inspection
Rejection and Rehearing
TABLE 1 <\/td>\n<\/tr>\n
3<\/td>\nCertification
Test Report
Product Marking
Packing and Package Marking
Keywords <\/td>\n<\/tr>\n
4<\/td>\nA1. TEST METHOD FOR DETERMINATION OF COMPLIANCE WITH CHEMICAL COMPOSITIONAL REQUIREMENT FOR ANTIMONY, ARSENIC, BISMUTH, LEAD, NICKEL, SELENIUM, AND TELLURIUM IN SPECIFICATION B216 BY ELECTROTHERMAL ATOMIZATION ATOMIC ABSORPTION SPECTROMETRY
A1.1 Scope
A1.2 Summary of Test Method
A1.3 Significance and Use
A1.4 Interferences
A1.5 Apparatus
A1.6 Reagents and Materials <\/td>\n<\/tr>\n
5<\/td>\nA1.7 Hazards
A1.8 Calibration
A1.9 Procedure
A1.10 Calculation
A1.11 Precision and Bias <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":"

B216-10 Standard Specification for Tough-Pitch Fire-Refined Copper—Refinery Shapes<\/b><\/p>\n\n\n\n\n
Published By<\/td>\nPublication Date<\/td>\nNumber of Pages<\/td>\n<\/tr>\n
ASTM<\/b><\/a><\/td>\n2010<\/td>\n6<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n","protected":false},"featured_media":34579,"template":"","meta":{"rank_math_lock_modified_date":false,"ep_exclude_from_search":false},"product_cat":[1130,2637],"product_tag":[],"class_list":{"0":"post-34578","1":"product","2":"type-product","3":"status-publish","4":"has-post-thumbnail","6":"product_cat-77-150-30","7":"product_cat-astm","9":"first","10":"instock","11":"sold-individually","12":"shipping-taxable","13":"purchasable","14":"product-type-simple"},"_links":{"self":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product\/34578","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/types\/product"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media\/34579"}],"wp:attachment":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media?parent=34578"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_cat?post=34578"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_tag?post=34578"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}