This part of ISO 1268 specifies a method of preparing reinforced-plastic test plates by resin transfer moulding (RTM). It is intended to be read in conjunction with ISO 1268-1.<\/p>\n
| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 3<\/td>\n | Fibre-reinforced plastics\ufffd\u2014 Methods of producing test plates\ufffd\u2014 <\/td>\n<\/tr>\n | ||||||
| 5<\/td>\n | Contents Page <\/td>\n<\/tr>\n | ||||||
| 6<\/td>\n | Foreword <\/td>\n<\/tr>\n | ||||||
| 7<\/td>\n | Fibre-reinforced plastics\ufffd\u2014 Methods of producing test plates\ufffd\u2014 1\ufffd\ufffd\ufffd Scope 2\ufffd\ufffd\ufffd Normative references 3\ufffd\ufffd\ufffd Health and safety 4\ufffd\ufffd\ufffd Principle <\/td>\n<\/tr>\n | ||||||
| 8<\/td>\n | 5\ufffd\ufffd\ufffd Materials 5.1\ufffd\ufffd\ufffd Reinforcement 5.2\ufffd\ufffd\ufffd Resin 6\ufffd\ufffd\ufffd Plate dimensions 7\ufffd\ufffd\ufffd Reinforcement content 8\ufffd\ufffd\ufffd Apparatus 8.1\ufffd\ufffd\ufffd Mould 8.2\ufffd\ufffd\ufffd Press with heated platens 8.3\ufffd\ufffd\ufffd Air-circulation oven 8.4\ufffd\ufffd\ufffd Resin tanks 8.5\ufffd\ufffd\ufffd Pump 8.6\ufffd\ufffd\ufffd Vacuum pump <\/td>\n<\/tr>\n | ||||||
| 9<\/td>\n | 8.7\ufffd\ufffd\ufffd Flexible tubing 8.8\ufffd\ufffd\ufffd Temperature and pressure control and recording equipment 9\ufffd\ufffd\ufffd Procedure 9.1\ufffd\ufffd\ufffd Preparation of preform 9.1.1\ufffd\ufffd\ufffd Examples of methods of producing preforms 9.1.2\ufffd\ufffd\ufffd The mass per surface area of the preform shall be such that the plates produced have the… 9.1.3\ufffd\ufffd\ufffd The preform design shall be such that it matches the shape of the mould and correct alig… 9.2\ufffd\ufffd\ufffd Resin injection and cure 9.2.1\ufffd\ufffd\ufffd Depending on the nature of the resin and reinforcement, different procedures may be requ… 9.2.2\ufffd\ufffd\ufffd Place the reinforcement in the cavity of the mould. Close the mould and clamp it shut wi… 9.2.3\ufffd\ufffd\ufffd Place the reinforcement in the cavity of the mould, close the mould and clamp it shut. C… 9.2.4\ufffd\ufffd\ufffd The injection-moulding process can also be used with highly reactive resins. Place the p… 9.2.5\ufffd\ufffd\ufffd For all methods, record the temperature, pressure, duration under pressure and cure time. 9.3\ufffd\ufffd\ufffd Stabilization <\/td>\n<\/tr>\n | ||||||
| 10<\/td>\n | 10\ufffd\ufffd\ufffd Verification of the characteristics of the plate obtained 10.1\ufffd\ufffd\ufffd General 10.2\ufffd\ufffd\ufffd Fibre content 10.3\ufffd\ufffd\ufffd Void content 10.4\ufffd\ufffd\ufffd Density 10.5\ufffd\ufffd\ufffd Dimensions of the plate 10.6\ufffd\ufffd\ufffd Degree of cure 10.7\ufffd\ufffd\ufffd Fibre alignment 11\ufffd\ufffd\ufffd Marking <\/td>\n<\/tr>\n | ||||||
| 11<\/td>\n | 12\ufffd\ufffd\ufffd Test plate preparation report <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Fibre-reinforced plastics. Methods of producing test plates – Resin transfer moulding<\/b><\/p>\n |