Included herein are complete general and dimensional data for the various types of square and hex bolts recognized as SAE Standard and commonly used in automotive and other ground based motor vehicles and industrial equipment. Also included are appendixes covering wrench openings for bolts and thread runout sleeve gages. The inclusion of dimensional data in this standard is not intended to imply that all of the products described are stock production sizes. Users are requested to consult with manufacturers concerning lists of stock production sizes.
Related products
-
ASCE 9780784477014 2013
Manual of Practice No. 124: – Inland Navigation – Channel Training Works Published By Publicationā¦
-
SAE J 1054:1999
Warning Lamp Alternating Flashers Published By Publication Date Number of Pages SAE 1999-07-15 4
-
BS 5975:2008+A1:2011
Code of practice for temporary works procedures and the permissible stress design of falsework Publishedā¦
-
BS EN 62020:1999:2006 Edition
Electrical accessories. Residual current monitors for household and similar uses (RCMs) Published By Publication Dateā¦
-
ASCE 9780784477038 2012
Failure Case Studies in Civil Engineering – Structures, Foundations, and the Geoenvironment Published By Publicationā¦
-
BS EN IEC 60512-23-3:2019
Connectors for electrical and electronic equipment. Tests and measurements – Screening and filtering tests. Testā¦
-
BS 6297:2007+A1:2008
Code of practice for the design and installation of drainage fields for use in wastewaterā¦
-
ASHRAE 15 01:2001 Edition
ASHRAE Standard 15 Safety Standard for Refrigeration Systems (ANSI approved) Published By Publication Date Numberā¦
-
SAE J 1057:1999
Identification Terminology of Earthmoving Machines Published By Publication Date Number of Pages SAE 1999-05-01 21
-
OR OSHA Division2 N/A
Oregon Occupational Safety and Health Standards – Oregon Administrative Rules, Chapter 437 – Division 2:ā¦
-
BS EN 50341-2-22:2022
Overhead electrical lines exceeding AC 1 kV – National Normative Aspects (NNA) for Poland (basedā¦
-
CSA C747-09 (R2019):2009 Edition
Energy efficiency test methods for small motors Published By Publication Date Number of Pages CSAā¦
-
BS EN IEC 62477-1:2023
Safety requirements for power electronic converter systems and equipment – General Published By Publication Dateā¦
-
BS 5975:2019 – TC
Tracked Changes. Code of practice for temporary works procedures and the permissible stress design ofā¦
-
BS EN 50341-2-22:2022 – TC
Tracked Changes. Overhead electrical lines exceeding AC 1 kV – National Normative Aspects (NNA) forā¦
-
CAN/CSA B137 SERIES-17:2017 Edition
Thermoplastic pressure piping compendium Published By Publication Date Number of Pages CSA 2017-01-01 396
-
BSI PD 6461-3:1995:2003 Edition
General metrology – Guide to the expression of uncertainty in measurement (GUM) Published By Publicationā¦
-
BSI PAS 43:2006
Safe working of vehicle breakdown, recovery and removal operations. Management system specification Published By Publicationā¦
-
BS EN 62209-1:2016 – TC:2020 Edition
Tracked Changes. Measurement procedure for the assessment of specific absorption rate of human exposure toā¦
-
NFPA 70E 2015
NFPA 70EĀ®: Standard for Electrical Safety in the WorkplaceĀ® Published By Publication Date Number ofā¦
-
IEEE 493 1998
IEEE Recommended Practice for the Design of Reliable Industrial and Commercial Power Systems (Gold Book)ā¦
-
BS EN 1999-1-1:2007+A2:2013:2014 Edition
Eurocode 9: Design of aluminium structures – General structural rules Published By Publication Date Numberā¦
-
BS 6400-3:2007
Specification for installation, exchange, relocation and removal of gas meters with a maximum capacity notā¦
-
IEEE 1394 1996
IEEE Standard for a High Performance Serial Bus Published By Publication Date Number of Pagesā¦
-
IEEE 524 2004
IEEE Guide to the Installation of Overhead Transmission Line Conductors Published By Publication Date Numberā¦
-
CSA/ANSI Z21.11.2:19:2019 Edition
Gas-fired room heaters, volume II, unvented room heaters Published By Publication Date Number of Pagesā¦
-
WRC 494:2004
Fracture-Safe and Fatigue Design Criteria for Detonation-Induced Pressure Loading in Containment Vessels Published By Publicationā¦
-
BS EN 13369:2018 – TC:2020 Edition
Tracked Changes. Common rules for precast concrete products Published By Publication Date Number of Pagesā¦
-
BSI PAS 43:2008
Safe Working of Vehicle Breakdown, Recovery and Removal Operations. Management System Specification Published By Publicationā¦
-
ASCE 9780784476888 2013
Hurricane Ike Field Investigations – A Report of Field Operations from October 3 – 6,ā¦
-
BS EN 1992-1-1:2023
Eurocode 2. Design of concrete structures – General rules and rules for buildings, bridges andā¦
-
CAN/CSA-B354.1-04 (R2016):2004 Edition
Portable Elevating Work Platforms Published By Publication Date Number of Pages CSA 2004-04-20 58
-
ASCE 9780784476352 2012
Earthquakes and Engineers – An International History Published By Publication Date Number of Pages ASCEā¦
-
BS EN IEC 60512-23-3:2019 – TC:2020 Edition
Tracked Changes. Connectors for electrical and electronic equipment. Tests and measurements – Screening and filteringā¦
-
ASHRAE Book 20thCenturyAirConditioning 2021
20th Century Air Conditioning Published By Publication Date Number of Pages ASHRAE 2021 200
-
CSA C22.2 NO. 1993-17:2017 Edition
Self-ballasted lamps and lamp adapters (Including revision history of 2021) Published By Publication Date Numberā¦
-
CSA Z98:19:2019 Edition
Passenger ropeways and passenger conveyors Published By Publication Date Number of Pages CSA 2019-03-01 161
-
BS EN 1999-1-1:2023
Eurocode 9. Design of aluminium structures – General rules Published By Publication Date Number ofā¦
-
BS EN 1562:1997:2006 Edition
Founding. Malleable cast irons Published By Publication Date Number of Pages BSI 2006 14
-
BS 8490:2007
Guide to siphonic roof drainage systems Published By Publication Date Number of Pages BSI 2007ā¦