ISO 11338-2:2003
$36.40
Stationary source emissions — Determination of gas and particle-phase polycyclic aromatic hydrocarbons — Part 2: Sample preparation, clean-up and determination
Published By | Publication Date | Number of Pages |
ISO | 2003-06 | 30 |
If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]
ISO 11338-2:2003 specifies procedures for sample preparation, clean-up and analysis for the determination of gas and particle phase polycyclic aromatic hydrocarbons (PAH) in stack and waste gases. The analytical methods are capable of detecting sub-microgram concentrations of PAH per cubic metre of sample, depending on the type of PAH and the flue gas volume sampled.
The methods described in ISO 11338-2:2003 are based on either high performance liquid chromatography (HPLC) or gas chromatography-mass spectrometry (GC-MS).
NOTE ISO 11338-1 describes three methods and specifies minimum requirements for the sampling of PAH in stack and waste gases.
Published Code | ISO |
---|---|
Published By | International Organization for Standardization |
Publication Date | 2003-06 |
Pages Count | 30 |
Language | France |
Edition | 1 |
File Size | 266.2 KB |
ICS Codes | 13.040.40 - Stationary source emissions |
Related products
-
BS EN ISO 1133:2005
Plastics. Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of…
-
BS ISO 11358-2:2014
Plastics. Thermogravimetry (TG) of polymers – Determination of activation energy Published By Publication Date Number…
-
BS ISO 11338-2:2003
Stationary source emissions. Determination of gas and particle-phase polycyclic aromatic hydrocarbons – Sample preparation, clean-up…
-
BS EN ISO 11138-5:2006
Sterilization of health care products. Biological indicators – Biological indicators for low-temperature steam and formaldehyde…
-
BS EN ISO 11138-2:2009
Sterilization of health care products. Biological indicators – Biological indicators for ethylene oxide sterilization processes…
-
JIS T 9266:2012
Assistive products for walking – Elbow crutches Published By Publication Date Number of Pages JIS…
-
BS EN ISO 11339:2010
Adhesives. T-peel test for flexible-to-flexible bonded assemblies Published By Publication Date Number of Pages BSI…
-
BS ISO 11358-2:2005
Plastics. Thermographimetry (TG) of polymers – Determination of activation energy Published By Publication Date Number…
-
BS ISO 1138:2007+A1:2012
Rubber compounding ingredients. Carbon black. Determination of sulfur content Published By Publication Date Number of…
-
BS EN ISO 11138-3:2009
Sterilization of health care products. Biological indicators – Biological indicators for moist heat sterilization processes…
-
BS EN ISO 11378-2:2001+A1:2017:2018 Edition
Textile floor coverings. Laboratory soiling tests – Drum test Published By Publication Date Number of…
-
CSA Z14161:11 (R2020):2011 Edition
Sterilization of health care products – Biological indicators – Guidance for the selection, use and…
-
BS EN ISO 11348-3:2008+A1:2018:2019 Edition
Water quality. Determination of the inhibitory effect of water samples on the light emission of…
-
BS ISO 11338-1:2003
Stationary source emissions. Determination of gas and particle-phase polycyclic aromatic hydrocarbons – Sampling Published By…
-
CSA Z14161:F11 (C2020):2011 Edition
Stérilisation des produits de santé – Indicateurs biologiques – Directives générales pour la sélection, l’utilisation…
-
BS 7208-3:1992
Contact lenses – Methods of test for contact lenses Published By Publication Date Number of…
-
AAMI 15882 2008 RA 2013
ANSI/AAMI/ISO 15882:2008/(R)2013 – Sterilization of health care products – Chemical indicators-Guidance for selection, use and…
-
ISO 11138-2:2006
Sterilization of health care products — Biological indicators — Part 2: Biological indicators for ethylene…
-
BS EN ISO 11138-2:2017
Sterilization of health care products. Biological indicators – Biological indicators for ethylene oxide sterilization processes…
-
ISO 11358-2:2005
Plastics — Thermogravimetry (TG) of polymers — Part 2: Determination of activation energy Published By…
-
ISO 11338-1:2003
Émissions de sources fixes — Détermination des hydrocarbures aromatiques polycycliques sous forme gazeuse et particulaire…
-
AAMI 14161 2009 RA 2014
ANSI/AAMI/ISO 14161-2009/(R)2014 – Sterilization of health care products – Biological indicators – Guidance for the…
-
ISO 11348-2:2007
Water quality — Determination of the inhibitory effect of water samples on the light emission…
-
BS EN ISO 11337:2004:2009 Edition
Plastics. Polyamides. Determination of e-caprolactam and w-laurolactum by gas chromatography Published By Publication Date Number…
-
BS EN ISO 11138-3:2017
Sterilization of health care products. Biological indicators – Biological indicators for moist heat sterilization processes…
-
BS EN ISO 1133:2000
Plastics. Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of…
-
BSI DD ISO/TS 15338:2009
Surface chemical analysis. Glow discharge Mass spectrometry (GD-MS). Introduction to use Published By Publication Date…
-
BS ISO 11336-1:2023
Large yachts. Strength, weathertightness and watertightness of glazed openings – Design criteria, materials, framing and…
-
BS EN ISO 11138-2:2006
Sterilization of health care products. Biological indicators – Biological indicators for ethylene oxide sterilization processes…
-
ISO 18472:2018
Sterilization of health care products — Biological and chemical indicators — Test equipment Published By…
-
BS EN ISO 11138-3:2006
Sterilization of health care products. Biological indicators – Biological indicators for moist heat sterilization processes…
-
BS EN ISO 11138-1:2006
Sterilization of health care products. Biological indicators – General requirements Published By Publication Date Number…
-
ISO 11378-2:2001
Textile floor coverings — Laboratory soiling tests — Part 2: Drum test Published By Publication…
-
BS EN ISO 11138-4:2006
Sterilization of health care products. Biological indicators – Biological indicators for dry heat sterilization processes…
-
BS EN ISO 11348-1:2008+A1:2018:2019 Edition
Water quality. Determination of the inhibitory effect of water samples on the light emission of…
-
BS EN ISO 11339:2005:2006 Edition
Adhesives. T-peel test for flexible-to-flexible bonded assemblies Published By Publication Date Number of Pages BSI…
-
BS EN ISO 11348-2:2008+A1:2018:2019 Edition
Water quality. Determination of the inhibitory effect of water samples on the light emission of…
-
CAN/CSA-ISO 11140-1:16 (R2021):2016 Edition
Sterilization of health care products – Chemical indicators – Part 1: General requirements Published By…
-
BS EN ISO 11337:2010:2011 Edition
Plastics. Polyamides. Determination of e-caprolactam and w-laurolactam by gas chromatography Published By Publication Date Number…
-
BS EN ISO 11138-4:2017
Sterilization of health care products. Biological indicators – Biological indicators for dry heat sterilization processes…