IEEE C62.45 2003
$60.13
IEEE Recommended Practice on Surge Testing for Equipment Connected to Low-Voltage (1000 V and less) AC Power Circuits
Published By | Publication Date | Number of Pages |
IEEE | 2003 | 94 |
Revision Standard – Active. The scope of this recommended practice is the performance of surge testing on electrical and electronic equipment connected to low-voltage ac power circuits, specifically using there commended test waveforms defined in IEEE Std C62.41.2TM-2002. Nevertheless, these recommendations are applicable to any surge testing, regardless of the specific surges that may be applied. This IEEE standards product is part C62 Family on Surge Protection.
PDF Catalog
PDF Pages | PDF Title |
---|---|
1 | IEEE Std C62.45-2002 Cover Page |
2 | Title Page |
3 | Abstract/Keywords |
5 | Introduction CAUTION Participants |
8 | CONTENTS |
10 | 1. Overview 1.1 Scope |
11 | 1.2 Purpose |
12 | 2. References |
13 | 3. Definitions 3.1 Technical terms 3.2 Special word usage |
14 | 4. Planning of surge testing: Basic objectives 4.1 General 4.2 Surge environment |
15 | 4.3 Types of tests 4.4 Results and consequences of the test |
16 | 4.5 Unpowered testing versus powered testing |
17 | 4.6 Withstand levels 4.7 Voltage and current waveforms |
19 | 4.8 Safety 5. Implementation of surge testing: Test equipment 5.1 General 5.2 Surge generators |
20 | 5.3 Point of test surge application 5.4 Coupling the surge to the EUT |
22 | 5.5 Monitoring the EUT |
24 | 6. Performance of surge testing: Test procedures 6.1 General 6.2 Limiting stresses 6.3 Nature of the EUT |
25 | 6.4 Safety |
26 | 7. Applying the test surge: Coupling and decoupling circuits 7.1 General 7.2 Requirements for surge coupling |
28 | 7.3 Impedance considerations 7.4 Requirements for surge decoupling |
29 | 7.5 Surge coupling |
33 | 8. Grounding 8.1 Grounding precautions |
35 | 8.2 Grounding practices in EUTs 9. Standard surge tests waveforms 9.1 General |
36 | 9.2 Standard waveforms |
40 | 9.3 Test procedures |
41 | 9.4 Equations for standard waveforms |
43 | 10. Additional surge test waveforms 10.1 General 10.2 Additional waveforms |
49 | 10.3 Equations for additional waveforms 11. Evaluating test results |
51 | Annex A (informative) SPD Class I test parameters A.1 General A.2 The IEC Class I test for SPDs A.3 Parameters for a 10/350 µs waveform |
53 | Annex B (informative) Complementary notes B.1 AC power interface (ac power port) |
54 | B.2 Average power (overstressing) B.3 Back filter B.4 Blind spots |
55 | B.5 Common mode (and normal mode) |
57 | B.6 Communications interface (control/signal port) |
58 | B.7 Coupler B.8 Coupling gap B.9 Current surging |
59 | B.10 Current transformers |
60 | B.11 Damage B.12 Design test |
61 | B.13 Diagnostic test B.14 Differential connection |
62 | B.15 Effective output impedance |
64 | B.16 Environment test versus component specification test |
65 | B.17 Equipment grounding conductor |
66 | B.18 Equipment under test (EUT) B.19 Fault current |
68 | B.20 Follow current B.21 Ground fault protection |
69 | B.22 Grounding conductor B.23 Grounding practices |
70 | B.24 Insulation coordination |
72 | B.25 Insulation degradation B.26 Insulation tracking B.27 Life consumption |
73 | B.28 Low voltage B.29 Monitoring B.30 Multiple surge |
74 | B.31 Noise B.32 Normal mode B.33 Partial discharge B.34 Phase angle |
75 | B.35 Powered testing |
76 | B.36 Production test B.37 Qualification test B.38 Repetition rate |
77 | B.39 Surge coupling |
78 | B.40 Surge event B.41 Surge let-through |
79 | B.42 Surge remnant B.43 Susceptibility B.44 Test conditions |
81 | B.45 Unforeseen consequences B.46 Unpowered testing B.47 Upset |
82 | B.48 Vulnerability B.49 Waveform: Voltage versus current |
84 | B.50 Withstand level |
85 | Annex C (informative) Practical hints on surge testing C.1 Surge measurements |
90 | C.2 Point of surge application and measurement C.3 Trial run on components |
91 | C.4 Cheesecloth specifications C.5 Smoke, sights, and sounds C.6 Does it make sense? |
93 | Annex D (informative) Bibliography |