BS ISO 8098:2002
$167.15
Cycles. Safety requirements for bicycles for young children
| Published By | Publication Date | Number of Pages |
| BSI | 2002 | 36 |
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 3 | TitlePage – Cycles�— Safety requirements for bicycles for young children |
| 5 | TableofContent – Contents Page |
| 6 | Foreword – Foreword |
| 7 | Introduction – Introduction |
| 9 | Scope – 1��� Scope |
| 10 | Clause1 – 3��� Subassemblies Subclause2 – 3.1��� General Subclause3 – 3.1.1��� Sharp edges Subclause3 – 3.1.2��� Protrusions Subclause4 – 3.1.2.1��� Exposed protrusions Subclause4 – 3.1.2.2��� Exclusion zone, protective devices and screw threads |
| 11 | Subclause4 – 3.1.2.3��� Location of exposed protrusions Subclause3 – 3.1.3��� Security and strength of safety-related fasteners Subclause4 – 3.1.3.1��� Security of screws Subclause4 – 3.1.3.2��� Minimum failure torque |
| 12 | Subclause2 – 3.2��� Brakes Subclause3 – 3.2.1��� Braking system Subclause4 – 3.2.1.1��� Bicycles with max. saddle height Subclause4 – 3.2.1.2��� Bicycles with maximum saddle height less than |
| 13 | Subclause3 – 3.2.2��� Hand-operated brake Subclause4 – 3.2.2.1��� Brake lever position Subclause4 – 3.2.2.2��� Brake lever dimensions Subclause4 – 3.2.2.3��� Cable brake assembly Subclause4 – 3.2.2.4��� Brake block and holder assembly |
| 14 | Subclause4 – 3.2.2.5��� Brake adjustment Subclause3 – 3.2.3��� Back-pedal brake Subclause3 – 3.2.4��� Strength of braking system Subclause4 – 3.2.4.1��� Hand-operated brake Subclause4 – 3.2.4.2��� Back-pedal brake Subclause3 – 3.2.5��� Braking performance Subclause4 – 3.2.5.1��� Hand-operated brake performance test Subclause4 – 3.2.5.2��� Back-pedal brake performance test |
| 15 | Subclause2 – 3.3��� Steering Subclause3 – 3.3.1��� Handlebars Subclause3 – 3.3.2��� Handlebar grips Subclause3 – 3.3.3��� Handlebar stem Subclause3 – 3.3.4��� Steering stability Subclause3 – 3.3.5��� Strength of steering assembly UntitledSubclause4 – 3.3.5.1��� The handlebar stem shall not fracture or undergo permanent deform… UntitledSubclause4 – 3.3.5.2��� The handlebar shall not move in relation to the stem when tested … UntitledSubclause4 – 3.3.5.3��� The handlebar shall not move in relation to the fork stem when te… Subclause2 – 3.4��� Frame/fork assembly Subclause3 – 3.4.1��� Impact test (falling mass) |
| 16 | Subclause3 – 3.4.2��� Impact test (falling frame/fork assembly) Subclause2 – 3.5��� Front fork Subclause2 – 3.6��� Wheels Subclause3 – 3.6.1��� Rotational trueness Subclause4 – 3.6.1.1��� General Subclause4 – 3.6.1.2��� Radial run-out tolerance Subclause4 – 3.6.1.3��� Axial run-out tolerance Subclause3 – 3.6.2��� Clearance Subclause3 – 3.6.3��� Static load test Subclause3 – 3.6.4��� Wheel retention Subclause4 – 3.6.4.1��� General Subclause4 – 3.6.4.2��� Front wheel retention |
| 17 | Subclause4 – 3.6.4.3��� Rear wheel retention Subclause2 – 3.7��� Tyres and tubes Subclause3 – 3.7.1��� Maximum inflation pressure Subclause3 – 3.7.2��� Compatibility of inflatable tyres and rims Subclause2 – 3.8��� Pedals and pedal/crank assembly Subclause3 – 3.8.1��� Pedal tread UntitledSubclause4 – 3.8.1.1��� The pedal tread surface shall be secured against movement within … UntitledSubclause4 – 3.8.1.2��� Pedals shall have Subclause3 – 3.8.2��� Pedal clearance Subclause4 – 3.8.2.1��� Ground clearance UntitledSubclause5 – 3.8.2.1.1��� With the bicycle unladen, any stabilizers removed, and with the… UntitledSubclause5 – 3.8.2.1.2��� Sprung suspension (if applicable) shall be depressed by applica… Subclause4 – 3.8.2.2��� Toe clearance |
| 18 | Subclause3 – 3.8.3��� Pedal/crank assembly kinetic test Subclause2 – 3.9��� Saddle Subclause3 – 3.9.1��� Limiting dimensions Subclause3 – 3.9.2��� Seat pillar Subclause3 – 3.9.3��� Saddle adjustment clamp |
| 19 | Subclause3 – 3.9.4��� Saddle strength Subclause2 – 3.10��� Drive system static load test Subclause2 – 3.11��� Chainguard Subclause2 – 3.12��� Stabilizers Subclause3 – 3.12.1��� Dimensions |
| 20 | Subclause3 – 3.12.2��� Vertical load test Subclause3 – 3.12.3��� Longitudinal load test Subclause2 – 3.13��� Instructions Subclause2 – 3.14��� Marking Clause1 – 4��� Test methods Subclause2 – 4.1��� General Subclause2 – 4.2��� Brake block test |
| 21 | Subclause2 – 4.3��� Braking system load test Subclause3 – 4.3.1��� Hand-operated brake Subclause3 – 4.3.2��� Back-pedal brake |
| 22 | Subclause2 – 4.4��� Hand-operated brake performance test |
| 23 | Subclause2 – 4.5��� Back-pedal brake performance test |
| 24 | Subclause2 – 4.6��� Steering assembly test Subclause3 – 4.6.1��� Handlebar stem Subclause4 – 4.6.1.1��� Torque test |
| 25 | Subclause4 – 4.6.1.2��� Static load test |
| 26 | Subclause3 – 4.6.2��� Torque test�— Handlebar and stem |
| 27 | Subclause3 – 4.6.3��� Torque test�— Handlebar stem and fork stem Subclause2 – 4.7��� Impact tests on frame/fork assembly Subclause3 – 4.7.1��� Falling mass test |
| 29 | Subclause3 – 4.7.2��� Falling frame/fork assembly test |
| 30 | Subclause2 – 4.8��� Static load test: wheel |
| 31 | Subclause2 – 4.9��� Pedal/crank assembly kinetic test Subclause2 – 4.10��� Static load test�— Saddle and pillar Subclause2 – 4.11��� Drive-system static load test Subclause3 – 4.11.1��� General |
| 32 | Subclause3 – 4.11.2��� Single-speed system Subclause3 – 4.11.3��� Multispeed system Subclause2 – 4.12��� Stabilizers�— Vertical load test |
| 33 | Subclause2 – 4.13��� Stabilizers�— Longitudinal load test |
| 34 | Subclause2 – 4.14��� Saddle strength test |
| 35 | Bibliography – Bibliography |
