BS ISO 13106:2014
$142.49
Plastics. Blow-moulded polypropylene containers for packaging of liquid foodstuffs
| Published By | Publication Date | Number of Pages |
| BSI | 2014 | 28 |
This International Standard provides the requirements of polypropylene resins intended for use in blow-moulded, round containers with capacities up to, and including two litres intended for the packaging of liquids for human consumption. This International Standard also provides tolerances on mass, dimensions, methods of sampling, testing, and performance requirements.
NOTE It is not to be implied that polypropylene resins are the only polymers suitable for these applications, as many other polymers, including PE-HD, PET, etc. are also suitable.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 6 | Foreword |
| 7 | Section sec_1 Section sec_2 Section sec_3 Section sec_3.1 1 Scope 2 Normative references 3 Terms and definitions |
| 8 | Section sec_3.2 Section sec_3.3 Section sec_3.4 Section sec_3.5 Section sec_3.6 Section sec_3.7 Section sec_3.8 Section sec_3.9 Section sec_3.10 Section sec_3.11 Section sec_3.12 |
| 9 | Section sec_3.13 Section sec_3.14 Section sec_3.15 Section sec_3.16 Section sec_3.17 Section sec_3.18 Section sec_3.19 Section sec_3.20 Section sec_3.21 Section sec_4 4 Raw material |
| 10 | Section sec_5 Section sec_6 Table tab_1 Section sec_7 Section sec_7.1 Section sec_7.2 Section sec_7.3 Section sec_7.4 Section sec_7.5 5 Container capacity 6 Container mass 7 Tolerance on dimensions 7.1 General 7.2 Wall thickness 7.3 Overall height (OH) 7.4 Diameter (D) 7.5 Neck height (H) |
| 11 | Section sec_7.6 Section sec_7.7 Section sec_7.8 Section sec_7.9 Section sec_8 Section sec_8.1 Section sec_8.2 Section sec_8.3 Section sec_8.4 Section sec_8.5 7.6 External neck diameter (E) 7.7 Internal neck diameter (I) 7.8 Thread diameter (T) 7.9 Neck ovality 8 Performance requirements 8.1 General 8.2 Closure leakage test 8.3 Drop impact resistance test 8.4 Stack load test 8.5 Leakage test |
| 12 | Section sec_8.6 Section sec_8.7 Section sec_9 Section sec_10 Section sec_10.1 Table tab_2 Section sec_10.2 8.6 Ink adhesion test 8.7 Compatibility test 9 Statutory marking 10 Sampling and criterion for conformity 10.1 Sampling criterion 10.2 Number of tests and criteria for conformity |
| 13 | Table tab_3 |
| 14 | Annex sec_A Table tab_a Figure fig_A.1 Annex A (normative) Container and neck finish descriptions |
| 15 | Annex sec_B Annex sec_B.1 Annex sec_B.2 Annex sec_B.3 Annex B (normative) Determination of brimful capacity |
| 16 | Annex sec_C Annex sec_C.1 Annex sec_C.2 Annex sec_C.2.1 Annex sec_C.2.2 Annex sec_C.2.3 Annex sec_C.3 Annex C (normative) Measurement of container wall thickness |
| 17 | Annex sec_D Annex sec_D.1 Annex sec_D.2 Annex sec_D.3 Annex D (normative) Measurement of container overall height |
| 18 | Annex sec_E Annex sec_E.1 Annex sec_E.2 Annex sec_E.2.1 Annex sec_E.2.2 Annex sec_E.2.3 Annex sec_E.3 Annex E (normative) Measurement of diameter for round container |
| 19 | Annex sec_F Annex sec_F.1 Annex sec_F.2 Annex sec_F.2.1 Annex sec_F.2.2 Annex sec_F.3 Annex F (normative) Measurement of neck height Measurement of neck height |
| 20 | Annex sec_G Annex sec_G.1 Annex sec_G.2 Annex sec_G.2.1 Annex sec_G.2.2 Annex sec_G.3 Annex G (normative) Measurement of neck and thread diameters and neck ovality Measurement of neck and thread diameters and neck ovality |
| 21 | Annex sec_H Annex sec_H.1 Annex sec_H.2 Annex sec_H.3 Annex sec_H.4 Annex H (normative) Drop impact resistance test Drop impact resistance test |
| 22 | Annex sec_I Annex sec_I.1 Annex sec_I.2 Annex I (normative) Stack load test Stack load test |
| 23 | Annex sec_J Annex sec_J.1 Annex sec_J.1.1 Annex sec_J.1.2 Annex sec_J.2 Annex sec_J.3 Annex J (normative) Leakage test Leakage test |
| 24 | Annex sec_K Annex sec_K.1 Annex sec_K.2 Annex K (normative) Ink adhesion test for printed containers Ink adhesion test for printed containers |
