BS EN 15101-2:2013
$142.49
Thermal insulation products for buildings. In-situ formed loose fill cellulose (LFCI) products – Specification for the installed products
| Published By | Publication Date | Number of Pages |
| BSI | 2013 | 26 |
This European Standard specifies requirements for in -situ formed loose-fill cellulose insulation (LFCI) products when installed as thermal insulation into walls, floors, galleries, roofs, lofts and ceilings.
This Part 2 is a specification for the installation checks for the installed products.It specifies the checks and tests to be used for the declarations made by the installer of the product.
This European Standard does not specify the required level of all properties to be achieved by a product to demonstrate fitness for purpose in a particular application. The required levels are to be found in regulations or non-conflicting standards.
Products with a declared thermal conductivity at 10 °C (mean temperature) greater than 0,060 W/(m × K) or a declared thermal resistance lower than 0,25 m2 × K/W are not covered by this European Standard.
This European Standard does not cover factory made cellulose mats, bats or quilts intended to be used for the insulation of buildings or in-situ cellulose products for the insulation of building equipment and industrial installations. Nor does it specify performance requirements.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 7 | 1 Scope 2 Normative references 3 Terms, definitions, symbols and abbreviations 3.1 Terms and definitions |
| 8 | 3.2 Symbols and abbreviations 3.2.1 Symbols used in this standard: 3.2.2 Abbreviations used in this standard |
| 9 | 4 Requirements 4.1 General 4.2 Declared installed insulation thickness and declared installed insulation density for open blow applications (e.g. lofts) 4.3 Declared installed insulation thickness and declared installed insulation density for cavity applications (e.g. frame wall, roof and floor constructions) 5 Test methods 5.1 General |
| 10 | 5.2 Declared installed insulation thickness 5.3 Declared installed insulation density 5.4 Frame method for the determination of declared installed density 5.5 Declared installed declared insulation density of cavity applications 5.5.1 Average cavity width 5.5.2 Machine output 5.5.3 Declared installed insulation density |
| 11 | 6 Guidelines for installation 7 Installer’s declaration |
| 12 | Annex A (normative) Open blow applications (lofts) – Determination of installed insulation thickness – Pin and plate method A.1 Apparatus A.2 Procedure |
| 14 | Annex B (normative) Cavity applications – Calculation for determining the declared installed insulation density in a construction B.1 Procedure B.2 Calculation |
| 15 | Annex C (normative) Cavity applications – Determination of average cavity width C.1 Procedure C.2 Calculation C.3 Floors |
| 16 | Annex D (normative) Cavity applications – Test box density (method of checking the blown density before installation into the wall) D.1 Apparatus D.2 Procedure D.3 Calculation |
| 17 | Annex E (informative) Example for installation guidelines E.1 Lofts E.1.1 Control tests made by the installer when preparing the product on site E.1.2 Installation procedure |
| 18 | E.1.3 Installer’s declaration |
| 19 | E.2 Walls E.2.1 Suitability of the building to receive the insulation |
| 20 | E.2.2 An example of a declaration form for use by the installer E.3 Frame constructions E.3.1 Suitability of the building to receive the insulation |
| 21 | E.3.2 An example of a declaration form for use by the installer E.4 Floors E.4.1 Suitability of the structure to receive the insulation |
| 23 | E.4.2 An example of a declaration form for use by the installer |
