BS EN 14814:2016 – TC:2020 Edition
$186.33
Tracked Changes. Adhesives for thermoplastic piping systems for fluids under pressure. Specifications
| Published By | Publication Date | Number of Pages |
| BSI | 2020 | 70 |
This European Standard specifies the requirements and test methods for adhesives used for joining the components of unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C), acrylonitrile-butadiene-styrene (ABS) and styrene copolymer blends (PVC+SAN) thermoplastic piping systems for fluids under pressure, independent of the application area.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 1 | compares BS EN 14814:2016 |
| 2 | TRACKED CHANGES Text example 1 — indicates added text (in green) |
| 44 | Contents Page |
| 46 | European foreword |
| 47 | Introduction |
| 48 | 1 Scope 2 Normative references 3 Terms and definitions |
| 49 | 4 Product characteristics 4.1 General considerations Table 1 — Intended use standard list Table 2 — Test pieces diametral clearance Table 3 — Test pieces setting time |
| 50 | 4.2 Resistance to pull out 4.3 Pressure resistance 4.4 Resistance for high temperature 4.5 Shelf life 4.6 Release of dangerous substances 4.7 Durability 5 Testing, assessment and sampling methods 5.1 Resistance to pull out |
| 51 | Table 4 — Requirements for the shear strength 5.2 Pressure resistance Table 5 — Pressure resistance |
| 52 | 5.3 Shelf life 5.4 Release of dangerous substances 5.5 Durability 6 Assessment and verification of constancy of performance — (AVCP) 6.1 General 6.2 Type testing 6.2.1 General |
| 53 | 6.2.2 Test samples, testing and compliance criteria Table 6 — Number of samples to be tested and compliance criteria |
| 54 | 6.2.3 Test reports 6.3 Factory production control (FPC) 6.3.1 General 6.3.2 Requirements 6.3.2.1 General |
| 55 | 6.3.2.2 Equipment 6.3.2.2.1 Testing 6.3.2.2.2 Manufacturing 6.3.2.3 Raw materials and components 6.3.2.4 Traceability and marking 6.3.2.5 Controls during manufacturing process |
| 56 | 6.3.2.6 Product testing and evaluation 6.3.2.7 Non-complying products 6.3.2.8 Corrective action 6.3.2.9 Handling, storage and packaging 6.3.3 Product specific requirements |
| 57 | 6.3.4 One-off products, pre-production products (e.g. prototypes) and products produced in very low quantity |
| 58 | 7 Marking, labelling and packaging |
| 59 | Annex A (informative) Additional characterization for adhesives for thermoplastic piping systems under pressure Table A.1 — List of additional characterization test methods and a suggested test frequency for adhesives for thermoplastic piping systems under pressure |
| 60 | Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Regulation ZA.1 Scope and relevant characteristics Table ZA.1 — Relevant clauses for adhesives for thermoplastic piping systems under pressure |
| 61 | ZA.2 Procedure for AVCP of adhesives for thermoplastic piping systems under pressure ZA.2.1 System(s) of AVCP Table ZA.2 — System of AVCP Table ZA.3 — Assignment of AVCP tasks for adhesives for thermoplastic piping systems under pressure under system 4 ZA.2.2 Declaration of performance (DoP) ZA.2.2.1 General ZA.2.2.2 Content |
| 62 | ZA.2.2.3 Example of DoP |
| 64 | ZA.3 CE marking and labelling |
| 65 | Figure ZA.1 — Example CE marking information on adhesive packaging |
| 66 | Figure ZA.2 — Example CE marking information on accompanying commercial documents |
| 67 | Bibliography |
