This document applies to metering pumps, dispensers and remote pumping units to be installed at liquid fuel filling stations, designed to dispense flammable liquid fuels into the tanks of motor vehicles, boats and light aircraft and into portable containers at flow rates up to 200 l · min^?1, and intended for use and storage at ambient temperatures between ?20 °C and +40 °C.

This document deals with all significant hazards, hazardous situations and events relevant to metering pumps, dispensers and remote pumping units, when they are used as intended and under the conditions foreseeable by the manufacturer (see Clause 4).

This document gives health and safety related requirements for the selection, construction and performance of the equipment.

This document does not specify a required performance level, PL_r, according to EN ISO 13849?1 .

This document does not deal with noise and with hazards related to transportation and installation.

This document does not include any requirements for metering performance.

Vapour recovery efficiency rates are not considered within this document.

Fuels other than the ones of subdivision Group IIA according to EN ISO/IEC 80079?20?1:2019 are excluded from this document.

This document does not apply to equipment for use with liquefied or compressed gases.

This document does not cover the installation of the emergency stop provisions for the liquid fuel filling station.

This document is not applicable to metering pumps, dispensers and remote pumping units, which are manufactured before the date of publication of this document by CEN.

PDF Catalog

PDF Pages	PDF Title
1	30443500
85	A-30368711
86	undefined
95	1 Scope 2 Normative references
97	3 Terms and definitions
102	4 List of significant hazards
103	5 Safety requirements and/or protective measures 5.1 Explosion protection measures 5.2 Selection of equipment 5.2.1 General
105	5.2.2 Pipe and hose permeability 5.2.3 Nozzle area — vapour releases only
108	5.2.4 Nozzle boot area
111	5.3 Safety requirements, protective measures, construction and performance 5.3.1 General requirements 5.3.1.1 General
112	5.3.1.2 Controls 5.3.1.3 Flow control
113	5.3.1.4 Flow rates 5.3.1.5 Working pressure 5.3.1.6 Stability 5.3.1.7 Vapour barriers 5.3.2 Electrical equipment 5.3.2.1 General
114	5.3.2.2 Lamp markings 5.3.2.3 Cabling insulation resistance 5.3.2.4 Cables used in hazardous areas
115	5.3.2.5 Insulation and isolation 5.3.2.6 Chemical cells in non-hazardous areas 5.3.3 Non-electrical equipment
116	5.3.4 Hydraulic equipment 5.3.4.1 General
117	5.3.4.2 Nozzle 5.3.4.3 Delivery hose assemblies 5.3.4.4 Air and/or vapour separator(s)
118	5.3.4.5 Float 5.3.4.6 Sight glass
119	5.3.4.7 Shear valve 5.3.4.8 High hose inlet joint area 5.3.5 Vapour recovery system
120	5.3.6 Housings 5.3.7 Ventilation 5.3.7.1 Vapour traps 5.3.7.2 Hydraulic unit 5.3.7.3 Hose cassette 5.3.7.4 Enclosures partially in a hazardous area
121	5.3.7.5 Column extensions 5.4 Safety requirements related to electromagnetic phenomena 6 Tests 6.1 Type tests 6.1.1 General 6.1.2 Sight glass test 6.1.2.1 Purpose 6.1.2.2 Impact test
122	6.1.2.3 Pressure test 1 6.1.2.4 Pressure test 2 6.1.3 Pressure test for fuel containment systems 6.1.3.1 Purpose 6.1.3.2 Procedure 6.1.3.3 Burst test 6.1.3.4 Leak test 6.1.4 Tests for unarmoured electric cables 6.1.4.1 Purpose 6.1.4.2 Solvent test
123	6.1.4.3 Impact test
125	6.1.4.4 Low temperature bend test 6.1.4.5 Voltage and insulation resistance tests 6.1.4.6 Flame transmission tests for unarmoured cables
127	6.1.5 Stability test 6.1.5.1 Purpose 6.1.5.2 Procedure
128	6.1.6 Pressure test for vapour recovery systems 6.1.6.1 Purpose 6.1.6.2 Procedure 6.1.7 Material assessment 6.1.7.1 Purpose 6.1.7.2 Procedure 6.1.8 Seal, gasket and float assessment 6.1.8.1 Purpose 6.1.8.2 Procedure
129	6.1.9 Electrical tests 6.1.9.1 Continuity of the protective bonding circuit 6.1.9.2 Insulation resistance tests 6.1.9.3 Voltage test 6.1.9.4 Functional tests 6.1.9.5 Resistance nozzle spout to dispenser earth
130	6.2 Routine tests 6.2.1 Electrical tests 6.2.2 Hydraulic tests
131	7 Information for use 7.1 General 7.2 Signals and warnings 7.3 Accompanying documents (Instruction manual)
132	7.4 Marking 8 Environmental aspects
133	Annex A (normative)Classification of vapour barriers A.1 General A.2 Vapour barrier Type 1 A.3 Vapour barrier Type 2
134	A.4 Typical vapour barrier arrangements A.4.1 Horizontal vapour barrier Type 1
135	A.4.2 Vertical vapour barrier Type 1
136	A.4.3 Horizontal vapour barrier Type 2
137	A.4.4 Vertical vapour barrier Type 2
140	Annex B (informative)Information on explosion protected equipment
141	Annex C (informative)Environmental aspects
143	Annex D (informative)Potentially explosive atmospheres associated with refuelling vehicles
145	Annex E (normative)Verification of requirements
149	Annex ZA (informative)Relationship between this European Standard and the essential requirements of Directive 2014/34/EU aimed to be covered
151	Annex ZB (informative)Relationship between this European Standard and the essential requirements of Directive 2006/42/EC aimed to be covered

Status	Definitive
Pages	154
Publication Date	2021-12-22
ISBN	978 0 539 19268 1
Standard Number	BS EN 13617-1:2021 – TC
Title	Tracked Changes. Petrol filling stations – Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units
Descriptors	Vending machines, Test methods, Measuring instruments, Performance, Safety measures, Protected electrical equipment, Fuel pumps, Equipment safety, Liquid fuels, Gasoline, Filling devices, Vapour barriers, Explosive atmospheres, Filling stations, Flammable atmospheres, Design, Hazards, Fire safety, Pumps
Publisher	BSI
Committee	PVE/393
ICS Codes	75.200 - Petroleum products and natural gas handling equipment