🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
ASTM-F1055:2011 Edition(Redline)

ASTM-F1055:2011 Edition(Redline)

$26.65

F1055-11 Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing (Redline)

Published By Publication Date Number of Pages
ASTM 2011 10
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Category:

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Abstract

This specification covers electrofusion-type polyethylene fittings for outside diameter controlled polyethylene pipe and tubing. Specimens shall be conditioned prior to joining at the minimum or maximum pipe temperature allowable for fusion. The fittings shall be subjected to several tests to determine conformance to minimum hydraulic burst pressure, sustained pressure, tensile strength, impact resistance, and joint integrity requirements. Fusion evaluation test for fitting failure and evaluation for voids shall also be conducted.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope

1.1 This specification covers electrofusion polyethylene fittings for use with outside diameter-controlled polyethylene pipe, covered by Specifications D2447 , D2513 , D2737 , D3035 , and F714 and crosslinked polyethylene (PEX), covered by Specification F2788 . Requirements for materials, workmanship, and testing performance are included. All requirements for joining PE electrofusion fittings to PE pipe shall also apply to joining PE electrofusion fittings to PEX pipe. Where applicable in this specification “ pipe ” shall mean “ pipe ” or “ tubing. ”

1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3 The following safety hazards caveat pertains only to the test method portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

D638 Test Method for Tensile Properties of Plastics D1248 Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable D1598 Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure D1599 Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings D1600 Terminology for Abbreviated Terms Relating to Plastics D2447 Specification for Polyethylene (PE) Plastic Pipe, Schedules 40 and 80, Based on Outside Diameter D2513 Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings D2737 Specification for Polyethylene (PE) Plastic Tubing D3035 Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter D3350 Specification for Polyethylene Plastics Pipe and Fittings Materials F412 Terminology Relating to Plastic Piping Systems F714 Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter F905 Practice for Qualification of Polyethylene Saddle-Fused Joints F2788 Specification for Metric-sized Crosslinked Polyethylene (PEX) Pipe

Keywords

Related products

ASTM-F1055
$26.65