ASTM-D4097 2010

$44.96

D4097-01(2010) Standard Specification for Contact-Molded Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks

Published By	Publication Date	Number of Pages
ASTM	2010	16

Guaranteed Safe Checkout

Categories: 23.020.10 - Stationary containers and tanks, ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

ASTM D4097-01-Reapproved2010

Historical Standard: Standard Specification for Contact-Molded Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks

ASTM D4097

Scope

1.1 This specification covers cylindrical tanks fabricated by contact molding for above-ground vertical installation, to contain aggressive chemicals at essentially atmospheric pressure, and made of a commercial-grade polyester or vinyl ester, resin. Included are requirements for materials, properties, design, construction, dimensions, tolerances, workmanship, and appearance.

1.2 This specification does not cover the design of vessels intended for pressure above hydrostatic, vacuum conditions, except as classified herein, or vessels intended for use with liquids heated above their flash points.

1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are provided for information purposes only.

Note 1—Special design consideration should be given to vessels subject to superimposed mechanical forces, such as earthquakes, wind load, or agitation, to vessels subject to service temperature in excess of 180°F (82°C), and to vessels with unsupported bottoms.

Note 2—There is no known ISO equivalent to this standard.

1.4 The following safety hazards caveat pertains only to the test method portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Keywords

above ground; atmosphere; contact-molded; polyester; vinylester; Aboveground storage tanks; Chemical resistance–plastics; Chemical-resistant nonmetallic materials; Containers–tanks; Corrosive service applications–plastics; Cylindrical tanks; Glass-fiber-reinforced (GRP) plastics–specifications; Installation–plastic pipe materials/applications; Joint construction; Laminates–plastic; Liquid environments; Outdoor service equipment; Plastics–glass-fiber reinforced products; Polyester plastics–specifications; Reinforced thermosetting plastics (RTP)–specifications; Resins–furan; Structural tanks; Tanks; Tolerances–plastics; Vinyl ester plastics

ICS Code

ICS Number Code 23.020.10 (Stationary containers and tanks)

DOI: 10.1520/D4097-01R10

PDF Catalog

PDF Pages	PDF Title
1	Scope Referenced Documents
2	Terminology Classification Materials and Manufacture Design Requirements
3	FIG. 1
4	FIG. 2
5	TABLE 1 TABLE 2
6	Laminate Construction Requirements TABLE 3 TABLE 4
7	FIG. 3 FIG. 4 TABLE 5
8	TABLE 6
9	FIG. 5
10	FIG. 6
11	Requirements Dimensions and Tolerances FIG. 7
12	Workmanship, Finish, and Appearance Test Methods TABLE 7
13	Product Marking Packaging and Package Marking Shipping FIG. 8
14	Keywords X1. HANDLING AND INSTALLATION X1.1 Handling X1.2 Installation
15	X2. WALL THICKNESSES X2.1 X3. DISHED BOTTOM TABLE X2.1 FIG. X3.1
16	X3.1

Additional information

Standard Title	D4097-01(2010) Standard Specification for Contact-Molded Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks
Published Code	ASTM
Publication Date	2010
Pages Count	16
ICS Codes	23.020.10 - Stationary containers and tanks