This Standard covers standard designs for the following: (a) plain and thread plug gage blanks to 12.010 in. maximum gaging diameter; (b) plain and thread ring gage blanks to 12.260 in. maximum gaging diameter; (c) involute and serrated spline plug and ring gage blanks to 8.000 in. major diameter; (d) straight-sided spline plug and ring gage blanks to major diameters of 8.000 in. for plugs and 6.000 in. for rings; (e) machine taper plug and ring gage blanks to 5.000 in. gaging diameter; (f) adjustable snap gages to 12 in.; (g) adjustable length gages to any desired length; (h) master disks up to 8.010 in. in diameter. Recommended general designs covering taper plug and ring gages for special applications, flush-pin gages, and flat plug gages are also included. This Standard is intended to deal only with the dimensions of blanks, frames, and fittings. However, it is expected that gages made from these blanks shall be finished in accordance with accepted good gage making practice with respect to accuracy and workmanship.

PDF Catalog

PDF Pages	PDF Title
3	ERRATA – January 2010
7	CONTENTS FIGURES
8	TABLES
10	MANDATORY APPENDICES
11	FOREWORD
13	COMMITTEE ROSTER
14	CORRESPONDENCE WITH THE B47 COMMITTEE
15	1 SCOPE 2 TERMINOLOGY
17	3 DETAILS OF CONSTRUCTION — AMERICAN GAGE DESIGN STANDARDS 3.1 Plain Cylindrical Plug Gage Blanks 3.1.1 Wire Type Design, Above 0.010 in. to and Including 1.010 in. 3.1.2 Taper Lock Design, Above 0.059 in. to and Including 1.510 in. 3.1.3 Trilock Design, Above 0.760 in. to and Including 8.010 in.
18	3.1.4 Annular Design Above 8.010 in. 3.2 Handles for Plain Cylindrical and Thread Plug Gage Blanks 3.3 Thread Plug Gage Blanks 3.4 Plain Ring Gage Blanks 3.5 Thread Ring Gage Blanks
19	3.6 Taper Plug and Ring Gages for Checking Taper Lock Handles and Gaging Members 3.7 Involute, Serrated, and Straight-Sided Spline Plug and Ring Gage Blanks 3.8 Machine Taper Plug and Ring Gage Blanks
20	3.9 Plain Adjustable Snap Gages 3.10 Adjustable Length Gages 3.11 Thread Snap and Indicating Thread Gages
21	3.12 Master Disks 4 OFFICIAL MONOGRAM FOR DESIGNATING PRODUCTS MADE TO AMERICAN GAGE DESIGN STANDARDS 5 APPLICATION OF AMERICAN GAGE DESIGN STANDARDS TO SPECIAL TYPES OF GAGES — RECOMMENDED PRACTICE 6 FLUSH PIN GAGES 7 DOUBLE-END BUILT-UP SNAP GAGES 8 FLAT PLUG GAGES
22	9 HANDLES, BILOCK, FOR FLAT PLUG GAGES
23	1 Plain Cylindrical Plug Gages, Details of Construction — Range Above 0.010 in. to and Including 8.010 in.
24	1 Handles for Wire Type Plain Cylindrical and Wire Type Thread Plug Gages, Wire Type Design – Range Above 0.010 in. to and Including 1.010 in.
25	2 Wire Type Plug Gage Handles, Details of Body
26	3 Wire Type Plug Gage Handles, Details of Capping Nut
27	4 Single-End Wire Type Plug Gage Handles, Details of Body
28	5 Wire Type Plug Gage Collet Nuts
29	6 Wire Type Plug Gage Collet Bushings, Size Ranges
30	7 Handles for Plain Cylindrical and Thread Plug Gages, Taper Lock Design — Range Above 0.059 in. to and Including 0.230 in.
31	8 Handles for Plain Cylindrical and Thread Plug Gages, Taper Lock Design — Range Above 0.230 in. to and Including 1.510 in.
32	9 Handles and Screws for Plain Cylindrical, Thread, and Spline (Involute, Serrated, Straight-Sided) Plug Gages, Trilock Design – Range Above 0.760 in. to and Including 8.010 in.
34	10 Plain Cylindrical Plug Gaging Members, Taper Lock Design — Range Above 0.059 in. to and Including 0.230 in. 11 Plain Cylindrical Plug Gage Blanks, Wire Type Design — Range Above 0.010 in. to and Including 1.010 in.
35	12 Plain Cylindrical Plug Gaging Members, Taper Lock Design – Range Above 0.230 in. to and Including 1.510 in.
36	13 Plain Cylindrical Plug Gaging Members, Trilock Design – Range Above 0.760 in. to and Including 2.510 in.
37	14 Plain Cylindrical Plug Gaging Members, Trilock Design – Range Above 2.510 in. to and Including 8.010 in.
38	2 Plain Cylindrical Plug Gages, Details of Construction — Range Above 8.010 in.
39	15 Plain Cylindrical Plug Gages, Annular Design — Range Above 8.010 in. to and Including 12.010 in.
40	3 Thread Plug Gages — Details of Construction
41	16 Thread Plug Gaging Members, Taper Lock Design — Range From No. 0 to No. 12, Inclusive
42	17 Thread Plug Gaging Members, Wire Type Design — Range Above 0.030 in. to and Including 1.010 in.
43	18 Thread Plug Gaging Members, Taper Lock Design – Range From 1/4 in. to and Including 11/2 in.
44	19 Thread Plug Gaging Members, Trilock Design – range Above 3/4 in. to and Inclulding 21/2 in.
45	20 Thread Plug Gaging Members, Trilock Design – Range Above 21/2 in. to and Including 8 in.
46	21 Thread Plug Gaging Members, Annular Design — Range Above 8.010 in.
47	22 Fine-Pitch Instrument Thread Plug Gaging Members, Taper Lock Design – Range No. 0 to 11/2 in., Inclusive
48	23 Fine-Pitch Instrument Thread Plug Gaging Members, Trilock Design — Range Above 11⁄2 in. to and Including 21⁄2 in.
49	24 Thread-Setting Plug Gaging Members, Truncated Type – Range No. 0 to 11/2 in., Inclusive
50	25 Thread-Setting Plug Gaging Members, Truncated Type — Range Above 11⁄2 in. to and Including 21⁄2 in.
51	26 Thread-Setting Plug Gaging Members, Truncated Type — Range Above 21⁄2 in. to and Including 61⁄2 in.
52	27 Taper Pipe-Thread Plug Gaging Members (L-1) – Range 1/16 in. to and Including 6 in.
53	28 Taper Pipe-Thread Plug Gaging Members for L-3 and Minor Diameter Check (6 Step)
54	4 Plain Ring Gages — Details of Construction
55	29 Plain Ring Gages — Range Above 0.010 in. to and Including 1.510 in.
56	30 Plain Ring Gages — Range Above 1.510 in. to and Including 12.260 in.
57	5 Thread Ring Gage Locking Device, Details of Construction — Range 1 in. to 51⁄2 in., Inclusive
58	31 Holders for Thread Ring Gages
59	6 Thread Ring Gages, Details of Construction — Range 0.060 in. to and Including 4.760 in.
60	7 Thread Ring Gages, Details of Construction — Range Above 0.510 in. to and Including 12.260 in.
61	32 Thread Ring Gages – Range No. 0 to and Including 43/4 in.; Also Fine-Pitch Instrument Thread Ring Gages, No. 0 to and Including No. 12
63	33 Thread Ring Gages — Range Above 4.760 in. to and Including 8.510 in.
64	34 Thread Ring Gages — Range Above 8.510 in. to and Including 12.260 in.
65	35 Fine-Pitch Instrument Thread Ring Gages – Range Above 0.240 in. to and Including 2.510 in.
67	36 Thread Ring Gage Adjusting Screws
68	37 Thread Ring Gage Sleeves
69	38 Thread Ring Gage Locking Screws
70	39 Solid, Nonadjustable Thread-Setting and Master (Reference) Ring Gage Blanks — Range 0.059 in. to 6.010 in.
72	40 Taper Pipe-Thread Ring Gages L1 and L2 — Range 1⁄16 in. to 8 in., Inclusive (Standard Basic Notch Design)
73	40A Taper Pipe-Thread Ring Gages — Step Limit Design
74	41 Plug and Ring Gages for Checking Handles and Gaging Member Taper Shanks of Taper Lock Plug Gages – Range Above 0.059 in. to and Including 1.510 in.
75	8 Three-Piece Spline Plug Gage Assembly
76	9 Spline Plug Gage Stands
77	42 Handles for Spline Plug Gages — Range Above 1.5 in. to and Including 8 in. 43 Washers for Spline Plug Gaging Members (Cup Type, Small) – Range Above 1.5 in. to and Including 5 in. 44 Washers for Spline Plug Gaging Members (Cup Type, Large) – Range Above 5 in. to and Including 8 in.
78	45 Involute, Serrated, and Straight-Sided Spline Composite and Sector Plug Gages – Range to and Including 2 in.
79	46 Involute, Serrated, and Straight-Sided Spline Composite and Sector Plug Gaging Members – Range Above 1.5 in. to and Including 8 in.
80	47 Involute, Serrated, and Straight-Sided Spline Composite and Sector Plug Gaging Members, Pilot Type – Range, Above 1.5 in. to and Including 8 in.
81	48 Involute, Serrated, and Straight-Sided Spline Tapered-Tooth Composite and Sector Plug Gages, Master and Wroking – Range to and Including 8 in.
82	49 Involute and Serrated Spline Composite and Sector Ring Gages — Range to and Including 8 in.
83	50 Involute and Serrated Spline Composite and Sector Ring Gages, Pilot Type – Range Above 1.5 in. to and Including 8 in.
84	51 Straight-Sided Spline Composite Ring Gages, Prong Type, for Space Widths 0.070 in. or Less – Range to and Including 1 in.
85	52 Straight-Sided Spline Composite Ring Gages, Prong Type, for Space Widths Greater Than 0.070 in. – Range to and Including 6 in.
86	53 Straight-Sided Spline Composite Alignment Ring Gages, Double-End Prong Type – Range Above 1 in. to and Including 6 in.
87	54 Built-Up Double-End Snap Gages for Tooth Thickness of Straight-Sided External Splines
88	55 Machine Taper Plug Gages, With Tang
90	56 Machine Taper Ring Gages, With Tang
92	57 Machine Taper Plug Gages, Without Tang
95	58 Machine Taper Ring Gages, Without Tang
96	59 Sizes of Combination Drills and Countersinks for Machine Taper Plug Gages
97	10 Adjustable Snap Gages, Details of Construction — Models A, B, C, and MC 11 Adjustable Snap Gages, Details of Construction — Model E
98	60 Plain Adjustable Snap Gages, Models A and B – Details of Frame
100	61 Plain Adjustable Snap Gages, Model C — Details of Frame
102	62 Plain Adjustable Snap Gages, Model MC — Details of Frame
103	12 Model MC Snap Gage Details
104	63 Adjustable Snap Gges, Extended Anvil, Model E – Details of Frame
106	64 Models A, B, C, and E Snap Gage, and Models K and L Adjustable Length Gage Adjusting Screws 65 Models A, B, C, and E Snap Gage, and Models K and L Adjustable Length Gage Locking Screws
107	66 Models A, B, C, and E Snap Gage, and Models K and L Adjustable Length Gage Locking Bushings and Nuts 67 Model A Snap Gage Gaging Pins
108	68 Models B, C, and E Snap Gage, and Models K and L Adjustable Length Gage Gaging Buttons 69 Model C Snap Gage and Model L Adjustable Length Gage Anvils
109	70 Model C Snap Gage and Model L Adjustable Length Gage Anvil Screws
110	71 Model E Snap Gage Anvil and Anvil Screws
111	72 Models A, B, C, E, and MC Snap Gage, and Models KA, KB, LA, and LB Adjustable Length Gage Marking Disks
112	13 Adjustable Length Gage, Double Sided, Models KA and KB, Details of Construction
113	14 Adjustable Length Gage, Progressive, Models LA and LB, Details of Construction
114	15 Adjustable Length Gage, Double Sided, Model KA, Details of Gage Heads
115	16 Adjustable Length Gage, Double Sided, Model KB, Details of Gage Heads
116	17 Adjustable Length Gage, Progressive, Model LA, Details of Gage Heads
117	18 Adjustable Length Gage, Progressive, Model LB, Details of Gage Heads
118	19 Adjustable Length Gages — Details of Spacing Tubes
119	73 Adjustable Length Gages, Parts List 74 Recommended Applicability of Adjustable Length Gage as Related to Product Tolerance
120	20 Master Disks — Styles 1, 2, and 3 21 Insulating Grips for Master Disks — Range Above 1.510 in. to and Including 8.010 in.
121	75 Master Disks – Range Above 0.105 in. to and Including 0.365 in.
122	76 Master Disks – Range Above 0.365 in. to and Including 1.510 in.
123	77 Master Disks — Range Above 1.510 in. to and Including 2.510 in.
124	78 Master Disks – Range Above 2.510 in. to and Including 8.010 in.
125	79 Insulating Grips for Master Disks — Range Above 0.105 in. to and Including 1.510 in.
126	80 Separator Plates for Master Disks — Range Above 1.510 in. to and Including 8.010 in. 81 Tie Rods For Master Disks — Range Above 1.510 in. to and Including 8.010 in.
127	22 Official Monogram for Designating Products Made to American Gage Design Standards 23 Recommended Design of Taper Plug Gage for Special Applications and Method of Dimensioning 24 Recommended Design of Taper Ring Gage for Special Applications and Method of Dimensioning
128	82 Recommended Design of Flat Plug Gages — Range Above 1.510 in. to and Including 8.010 in.
129	83 Recommended Design of Barrel Type Flush Pin Gage
130	25 Recommended Design of Bar Type Flush Pin Gage 26 Recommended Design of Small Countersink Type Flush Pin Gage — Range 3⁄4 in. to 11⁄2 in.
131	27 Recommended Design of Large Countersink Type Flush Pin Gage 28 Application of Countersink Type
132	29 Recommended Design of Small Built-Up Snap Gage 30 Recommended Design of Large Built-Up Snap Gage
133	84 Flat Plug Gage — Additional Specifications 85 Handle for Flat Plug Gage
135	I CONVERSION TABLE FROM INCH TO MILLIMETER
138	II METRIC EQUIVALENTS OF SELECTED TABLES

Published By	Publication Date	Number of Pages
ASME	2007	150


PDF Format	Searchable	Printable	Preview Now

Standard Title	ASME B47.1 – 2007(R2022) – Gage Blanks with Errata
Published Code	ASME
Publication Date	2007
Pages Count	150

ASME B47.1 2007 w Errata 012010 R2022

PDF Catalog

Related products

IEEE 8802-3-2014