IEC 61169-51:2015 provides information and rules for the preparation of detail specifications (DS) for type QLI R.F. coaxial connectors with quick lock. The connectors are normally used with 50 Ohms corrugated cable and flexible cables for middle power applications in an operating range up to 6 GHz. It describes the interface dimensions for general purpose connectors with gauging information and the mandatory tests selected from IEC 61169-1 applicable to all detail specifications relative to type QLI connectors. This specification indicates the recommended performance characteristics to be considered when writing a DS and covers all tests schedules and inspection requirements.<\/p>\n
| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 6<\/td>\n | English \n CONTENTS <\/td>\n<\/tr>\n | ||||||
| 8<\/td>\n | FOREWORD <\/td>\n<\/tr>\n | ||||||
| 10<\/td>\n | INTRODUCTION <\/td>\n<\/tr>\n | ||||||
| 11<\/td>\n | 1 Scope 2 Normative references <\/td>\n<\/tr>\n | ||||||
| 12<\/td>\n | 3 Mating face and gauge information 3.1 Dimensions \u2013 General connectors 3.1.1 Connector with socket-centre contact Figures \n Figure 1 \u2013 Connector with socket-centre contact with 2 options(for dimensions and key, see Table 1) <\/td>\n<\/tr>\n | ||||||
| 13<\/td>\n | Figure 2 \u2013 Detail of bayonet lock groove, option 1 (for dimensions and key, see Table 1) Figure 3 \u2013 Detail of bayonet lock groove, option 2 (for dimensions and key, see Table 1) <\/td>\n<\/tr>\n | ||||||
| 14<\/td>\n | Figure 4 \u2013 Female centre contact (for dimensions and key, see Table 1 <\/td>\n<\/tr>\n | ||||||
| 15<\/td>\n | Tables \n Table 1 \u2013 Dimensions of connector with socket-centre contact <\/td>\n<\/tr>\n | ||||||
| 16<\/td>\n | 3.1.2 Connector with pin-centre contact Figure 5 \u2013 Connector with pin-centre contact (for dimensions and key, see Table 2) Figure 6 \u2013 Details of pin-centre contact (for dimensions, see Table 2) <\/td>\n<\/tr>\n | ||||||
| 17<\/td>\n | Table 2 \u2013 Dimensions of connector with pin-centre contact <\/td>\n<\/tr>\n | ||||||
| 18<\/td>\n | 3.2 Gauges for connector with socket-centre contact 3.2.1 Centre contact 3.2.2 Test procedure Figure 7\u2013 Gauge pin for socket-centre contact (for dimensions, see Table 3) Table 3 \u2013 Gauge dimensions for socket-centre contact <\/td>\n<\/tr>\n | ||||||
| 19<\/td>\n | 3.2.3 Gauge for outer contact 4 Quality assessment procedures 4.1 General 4.2 Ratings and characteristics Figure 8 \u2013 Gauge ring for socket outer contact (for dimensions, see Table 4) Table 4 \u2013 Dimensions of gauge ring for socket outer contact <\/td>\n<\/tr>\n | ||||||
| 20<\/td>\n | Table 5 \u2013 Rating and characteristics <\/td>\n<\/tr>\n | ||||||
| 22<\/td>\n | 4.3 Periodic tests Table 6 \u2013 Acceptance tests <\/td>\n<\/tr>\n | ||||||
| 23<\/td>\n | Table 7 \u2013 Periodic tests <\/td>\n<\/tr>\n | ||||||
| 24<\/td>\n | 4.4 Procedures for the qualification approval 4.4.1 Quality conformance inspection 4.4.2 Qualification approval and its maintenance 5 Instructions for preparation of detail specifications (DS) 5.1 General 5.2 Identification of the component <\/td>\n<\/tr>\n | ||||||
| 25<\/td>\n | 5.3 Performances 5.4 Marking, ordering information and related matters 5.5 Selection of tests, test conditions and severities <\/td>\n<\/tr>\n | ||||||
| 26<\/td>\n | 5.6 Blank detail specification pro-forma for type QLI connector <\/td>\n<\/tr>\n | ||||||
| 31<\/td>\n | 6 Marking 6.1 Marking of component 6.2 Marking and contents of package <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Radio-frequency connectors – Sectional specification for RF coaxial connectors with inner diameter of outer conductors 13,5 mm with bayonet lock. Characteristic impedance 50 O (type QLI)<\/b><\/p>\n |