BS EN ISO 2813:2014
$142.49
Paints and varnishes. Determination of gloss value at 20 degrees, 60 degrees and 85 degrees
| Published By | Publication Date | Number of Pages |
| BSI | 2014 | 32 |
This International Standard specifies a method for determining the gloss of coatings using the three geometries of 20°, 60° or 85°. The method is suitable for the gloss measurement of non-textured coatings on plane, opaque substrates.
NOTE On test specimens different from these mentioned above, comparative gloss measurements are possible. However, it is not ensured that the obtained gloss values correspond to the visual gloss perception (see Annex A).
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 4 | Foreword |
| 6 | Foreword |
| 7 | Section sec_1 Section sec_2 Section sec_3 Section sec_3.1 Section sec_3.2 Section sec_3.3 1 Scope 2 Normative references 3 Terms and definitions |
| 8 | Section sec_4 Section sec_5 4 Principle 5 Basic principles of the gloss measurement |
| 9 | Table tab_a Figure fig_1 |
| 10 | Figure fig_2 Section sec_6 Section sec_6.1 Section sec_6.1.1 6 Apparatus and calibration equipment 6.1 Glossmeter |
| 11 | Table tab_b Figure fig_3 Section sec_6.1.2 |
| 12 | Table tab_1 Section sec_6.1.3 Section sec_6.1.4 |
| 13 | Section sec_6.2 Section sec_6.2.1 Section sec_6.2.2 Section sec_6.2.3 Section sec_6.2.4 6.2 Measurement standards (certified reference material, working measurement standards) |
| 14 | Section sec_7 Section sec_7.1 Section sec_7.2 Section sec_7.3 Section sec_7.4 Section sec_8 Section sec_8.1 Section sec_8.2 7 Test panels 7.1 Substrate 7.2 Preparation and coating 7.3 Drying and conditioning 7.4 Thickness of coating 8 Calibration and adjustment of the glossmeter 8.1 Preparation of the apparatus 8.2 Zero point check |
| 15 | Section sec_8.3 Section sec_9 Section sec_9.1 Section sec_9.2 8.3 Calibration and adjustment 9 Procedure 9.1 Selection of geometry 9.2 Gloss measurement |
| 16 | Section sec_10 Section sec_10.1 Section sec_10.2 Table tab_2 Section sec_10.3 Table tab_3 Section sec_11 10 Precision 10.1 General 10.2 Repeatability limit 10.3 Reproducibility limit 11 Test report |
| 18 | Annex sec_A Annex sec_A.1 Annex sec_A.2 Table tab_d Figure fig_A.1 Annex sec_A.3 Annex A (normative) Possible sources of error |
| 19 | Table tab_e Figure fig_A.2 Annex sec_A.4 Table tab_f Figure fig_A.3 |
| 20 | Table tab_g Figure fig_A.4 Annex sec_A.5 |
| 21 | Annex sec_B Annex sec_B.1 Annex sec_B.2 Annex B (normative) Calibration standards |
| 22 | Annex sec_B.3 |
| 23 | Annex sec_C Annex sec_C.1 Table tab_h Figure fig_C.1 Annex C (informative) Gloss calculation of primary reference standards |
| 24 | Annex sec_C.2 |
| 25 | Table tab_C.1 |
| 27 | Annex sec_D Annex sec_D.1 Annex sec_D.2 Annex sec_D.3 Annex sec_D.4 Annex sec_D.5 Table tab_D.1 Annex D (informative) Details on precision |
| 29 | Reference ref_1 Reference ref_2 Reference ref_3 Reference ref_4 Reference ref_5 Reference ref_6 Reference ref_7 Reference ref_8 Bibliography |
Related products
-
ISO 2813:2014
Paints and varnishes — Determination of gloss value at 20°, 60° and 85° Published By…
